Frigidaire Dishwasher Not Draining: When your dishwasher is unable to discharge the remaining water, it can be extremely aggravating. After it sits in the dishwasher for too long, the used water begins to smell unpleasant. This makes being in your kitchen intolerable while the dishwasher door is opened. It is also costly to hire a professional to fix the drainage system.
The simple solution is to learn how to repair the dishwasher on your own. Repairing the drainage system is not as difficult as most people believe. Dishwashers come in a variety of models, which may result in minor differences in the repair process. We’ll go over why your Frigidaire dishwasher isn’t draining properly and how to fix it in this article.
7 Reasons Why Frigidaire Dishwasher Not Draining
The first step in finding a remedy is figuring out why your Frigidaire dishwasher isn’t draining properly. The following are several drainage defects that may impede the drainage process:
- Hose for Drainage
Your dishwasher’s drain pipe connects to the garbage disposal. The connection is usually found under your sink. A clogged drain pipe could be the cause of your Frigidaire dishwasher not draining. Drainage can be restricted in two ways due to a malfunctioning drain hose:
- Food debris is the source of obstruction.
- An impediment induced by the creation of a kink.
A kink in the drain tube might lead to a puncture. Because it is the problem, signs of leakage in the drainpipe where there is a kink simplify your troubleshooting. If your drain hose is kinked, we recommend that you replace it.
A defective food chopper in your dishwasher can lead to food debris collection and an obstruction in the drain hose. The drain hose from the pump should be removed and cleaned. If you’re seeking drain cleaners, go to a Guide Pro. However, this is only a temporary fix since if the food chopper is not fixed, the drain line will become clogged again owing to food debris.
- Drain Valves
Drain valves are found in close proximity to the motor. They are in charge of allowing wastewater to exit your dishwasher while also avoiding backflow. Food material frequently clogs the valves, preventing water from escaping the dishwasher. Clean the dirt off the valve by removing it.
However, if the valve is found to be defective, it must be replaced. Valve failures cannot be fixed. Most defective valves enable filthy water to run back into the dishwasher or do not fully open. To determine if the valve is the faulty component. Remove the drain hose and fill your dishwasher with water before attempting to drain it. To catch the drained water, use a bucket. During the draining process, you will notice that the valve opens and does not close or does not drain entirely.
- Pump and Motor for Drainage
A defective pump in a Frigidaire model is uncommon, but it does happen. The water from your dishwasher is drained using a drain pump with an impeller. The pump could be problematic for a variety of reasons. The pump has been obstructed by a foreign object. Most of the time, it’s shards of broken glass. When you start the cycle, you’ll hear a small humming noise from the engine. This is a sign that there is anything strange in the drain pump.
Disconnect the feeder hose and any other connections that could be damaged while moving the dishwasher around to fix it. Disconnect the anti-flood switch after unscrewing the dishwasher’s base plate. Disconnect the feeder hose and any other connections that could be damaged while moving the dishwasher around to fix it. Disconnect the anti-flood switch after unscrewing the dishwasher’s base plate.
Screws hold the pump in place most of the time. Remove it by unscrewing it and twisting and pulling it out. You must be cautious when handling the screws and when removing the pump. If there is any difficulty when removing the pump, look for a connector or screw that is holding it in place. Check the impeller for any dirt or foreign items that may have obstructed it. Scraping off the debris is a simple way to clean it. Then, with your finger, try to rotate the impeller to see if it’s turning.
Your Frigidaire dishwasher may not drain water because the motor is not operating or is running in the wrong direction. Verify that the motor is spinning in the correct direction. Use a meter to see if the circuit reaches the terminals if the motor is not moving. If there is current in the terminals, your drain pump is not working due to a fault with the motor’s winding or because the motor has seized. A seized motor should be replaced as soon as possible.
If the current does not reach the terminals, the problem could be due to a malfunctioning electric control, timer, or door switch. If you’re not knowledgeable about contacts and electricity, you’ll need to hire a professional to address the technical issues.
- Timer
Your dishwasher’s timer is usually found on the control panel. It is in charge of both the motor and the drain solenoid. A malfunctioning timer could be the cause of your Frigidaire dishwasher not draining wastewater. A broken timer should be replaced as soon as possible.
You’ll need your dishwasher’s wiring and schematics to figure out if your timer is broken. The wiring layout and schematics of different Frigidaire dishwashers differ. You’ll be able to pinpoint the particular timer contacts in charge of the drainage system. You can troubleshoot by testing the current’s continuity.
If the timer receives current but does not reflect current out, the timer is malfunctioning. If there is currently coming out of the wire, follow it until the current breaks. If you notice a problem with the wires, you can replace them.
- Garbage Disposer
Your Frigidaire dishwasher may fail to drain the remaining water if you use the garbage disposer. It’s possible that the error occurred during installation or that it’s clogged. A solid blockage in the garbage disposer’s drain tube can obstruct drainage. This is particularly common with newly installed garbage disposals. Remove the plug to see if the drainage issue has been resolved. If you’ve been using your dishwasher, make sure the waste disposal is working properly.
Remove the drain hose and clean the disposer’s and drain hose’s joint. Examine the material in the blockage to see if it is made up of larger particles. If the particles are larger, you should also examine your food processor.
- Double-check the ball
You may notice your dishwasher draining occasionally, but after a while, you will notice water at the bottom of your dishwasher. The backflow of water from the dishwasher could be the cause of this.
A check ball is a tiny plastic ball that prevents water from flowing backward through a check valve. Drainage through the check valve is impeded when the check ball becomes trapped. To free the ball, use a screwdriver and oil.
- Drainage Basket Is Clogged
In many dishwashers, this is the most prevalent cause of drainage issues. A filter in the drainage system stops food debris from passing through. To reveal the drainage basket, manually remove all residual water. You should proceed with caution because the drainage basket may be clogged with glass fragments. Bolts or screws hold the drainage basket in place. Remove the basket and clean around the filters after undoing them.
The most difficult component of repairing your dishwasher drainage system is troubleshooting. When you know what the problem is, and you have the necessary tools, solving it isn’t difficult. There are some technical drainage issues that will necessitate the assistance of a professional.
If you are having drainage issues that are mostly caused by the control panel, it is recommended that you visit an expert if you are unsure how to solve the problem.